Vintage Mens Shoe Brands

Vintage Shoe Sizing and Terms

This post covers both vintage shoe sizing and the terms that are often found in vintage shoes. I added a number of photos to illustrate the sizing and terms. I am not going to cover shoe styles since there are plenty of other websites that go deep into the various shoes styles.

This is a working list that I started last year. I will keep it up to date with additions or changes. If you have something to add or if I have a wrong definition for a term (it happens), please leave a comment to correct the information.

Vintage Shoe Sizing

Shoe Size 4115 or 11.5 D
Size 11.5 D (4115)

A frequent issue with pre-1960s shoes is that the pair will not have a standard US size listed on the box or inside the shoes (i.e. size 10.5 E). When this is the case, check the inside of the shoe for a group of numbers that is 3 or 4 characters long. If found, this is likely the encoded shoe size. The first digit represents the width (A=1, B=2, etc), and the second set of digits are the length (105 is 10.5). For a 10.5 E pair, the encoded size would be “5105”. Below is a chart for converting the encoded size to standard US shoe size.

A B C D E
6.0 160 260 360 460 560
6.5 165 265 365 465 565
7.0 170 270 370 470 570
7.5 175 275 375 475 575
8.0 180 280 380 480 580
8.5 185 285 385 485 585
9.0 190 290 390 490 590
9.5 195 295 395 495 595
10.0 1100 2100 3100 4100 5100
10.5 1105 2105 3105 4105 5105
11.0 1110 2110 3110 4110 5110
11.5 1115 2115 3115 4115 5115
12.0 1120 2120 3120 4120 5120

These are a few visual examples for identifying the encoded size for a vintage pair of shoes.

Pair of Jarman 490 or 9 D shoes
Pair of Jarman 490 or 9 D shoes
Pair of Hanover shoes sized 3100 or 10 C
Pair of Hanover shoes sized 3100 or 10 C
Pair of boots sized 585 or 8.5 E
Pair of boots sized 585 or 8.5 E
Thom McAn shoes sized 2115 or 11.5 B
Thom McAn shoes sized 2115 or 11.5 B
Vintage Weyenberg shoes in size 460 or 6 D
Vintage Weyenberg shoes in size 460 or 6 D

Shoe Length by Measurement

When you still can’t find the size of the shoe, you can use the chart below to help find the shoe length. I have found measuring the insole, not the outsole, gives you the best representation of the shoe size. The measurements below are the length of the insole (what’s the insole? see below), and it should be taken with a measuring tape. I obtained these measurements from a orthotics manual.

US Size  Insole (in/cm)
6.0 10″ / 25.5 cm
6.5 10 3/16″ / 25.9 cm
7.0 10 5/16″ / 26.3 cm
7.5 10 9/16″ / 26.7 cm
8.0 10 5/8″ / 27 cm
8.5 10 7/8″ / 27.6 cm
9.0 11″ / 28 cm
9.5 11 3/16″ / 28.4 cm
10.0 11 5/16″ / 28.8 cm
10.5 11 1/2″ / 29.2 cm
11.0 11 3/4″ / 29.8 cm
11.5 11 7/8″ / 30.1 cm
12.0 12″ / 30.5 cm

Shoe Terms

Below are a list of terms you might find on the inside or outside of the shoe.

ANSI Z41 – American National Standards Institute approved footwear offering a protective toe (usually steel), and potentially having impact and compression protection.

Nettleton ANSI rated safety shoe
Nettleton ANSI rated safety shoe

Combination Last – the shoe form has different widths for the ball and heel of the foot. You will see this as part of the shoe width (i.e “D/B”). The larger size is the width of the ball and the smaller is the width of the heel.

Hanover Combination last where the ball of the foot is D and instep is B
Hanover Combination last where the ball of the foot is D and instep is B

Corfam – Synthetic, breathable leather made by DuPont from 1964 to 1971. Continues to be used in shoes today. Looks somewhat like polished cobbler or shell cordovan.

Insole – This is a layer of leather (usually), that covers the sole and is the foundation of the shoe. There is often another layer of material covering the insole partially (heel pad) or entirely. Sometimes referred as the innersole.

Alden leather insole and heel pad

Last – The wooden or plastic form over which a shoe was constructed. The last gives the shoe its distinctive shape.

Wooden shoe last
Wooden shoe last
Handlasted Bostonian Crown Windsor
Hand lasted Bostonian Crown Windsor

Lining – material that lines the inside of the shoe. The lining in vintage shoes is usually made of sheepskin or tough cotton drill.

Cotton drill shoe lining
Cotton drill shoe lining

Made in … – The country the shoe was made in. Prior to the 80s, most shoes from US manufacturers were made in the USA. If there is no “Made in” label, its likely the shoes were made in the USA.

Poromeric Upper – A synthetic leather upper. Often seen in military shoes or faux reptile leather shoes. See Corfam.

Outsole – the bottom of the shoe that is in direct contact with the ground. In vintage shoes, the sole is usually leather but can also be made from rubber resin.

Rubber outsoles on a pair of Stuart Mcguire shoes
Rubber outsoles on a pair of Stuart Mcguire shoes
Leather outsole on a pair of Cordwainer Wright cap toes
Leather outsole on a pair of Cordwainer Wright cap toes
Neolite outsole
Goodyear Neolite rubber outsole on a pair of Thom McAn shoes

Shank – A curved piece of steel or fiberglass built into the middle portion of a shoe that provides support. You will never see one but occasionally it is mentioned.

Upper – The visible leather portion of the shoe above the sole.

Beautiful vintage shell cordovan upper
A Stuart Mcguire pair where only the upper is leather. The rest of the shoe is plastic, fabric or rubber




13 thoughts on “Vintage Shoe Sizing and Terms”

  1. David, thanks for posting all this terminology. One quibble though. I thought that a combination last indicated the heel width was less than the ball width. I don’t believe it has anything to do with the instep. Most manufacturers have changed to making the heels smaller (usually by 2 sizes) than the ball measurement, called a combination last. Perhaps the reason is because a larger portion of the population have narrow heels than previous generations. For example, 11.5 C/A means C width at ball with an A heel. Alden and Nettleton (and possibly others) write the same measurements as 11.5 A/C (heel first). Some old timers, like Russell Moccasin, may state the same as “11.5 A, ball to C”.

  2. David thank you for your informative site . I enjoy the shoes and your sense of humor .

  3. David thank you for your informative site . I enjoy the shoes and your sense of humor .

  4. This is not exclusive to this post, but for the whole site which I’m just discovering. Everything is so amazing!!! You are an amazing person. So much valuable information here for me to learn. Thank you very much.

  5. When I was selling shoes in the early ’70s, shoe salesmaen’s slang for widths was “Benny” for a B width, “Charlie” for C, “David for D, and I think it was “Eddie” for E. I can’t remember if A width was “Andy”, or something else.

  6. This is a very informative post, and I love the spectator wingtips at the top of the article. I’m looking for a pair just like them!

Leave a Reply to Toe Blake Eddie Shore Cancel reply

Your email address will not be published. Required fields are marked *